RasPad - love at first byte RasPad - feast your pis on this RasPad - makers gonna make RasPad - pi in a box (with a screen!) RasPad - less mess, more making RasPad - the low stress, no mess, p...
RasPad - love at first byte RasPad - feast your pis on this RasPad - makers gonna make RasPad - pi in a box (with a screen!) RasPad - less mess, more making RasPad - the low stress, no mess, p...
@CerberusStyle Thanks. I'm a complete idiot. The accelshim was still in my box. Not sure how I missed that. However, upon opening the case again, I also damaged my display cable with the screwdrive...
@Isaac Linder ok that means the PI can not see the accelshim and why i2cdetect shows as empty, go to Menu / preferences / raspberry pi configuration click the interfaces tabenable i2c interface.c...
very nice product...
@CerberusStyle I did and got past that error. I failed to mention that. The new error is this: pi@raspberrypi:~/.config/lxsession/LXDE-pi $ sudo auto-rotator calibrate Traceback (most recent call...
@Nick Crosby i didnt think i have ever seen a red light on my shim and its working fine. 😕
@Isaac Linder yer that raspberry pi os 32bit thats fine and will work, did you do as i said and manually create the autostart file in that location and try to run again ??
@CerberusStyle - Sorry that was probably me being new to Raspberry Pi. I used the top recommended version from the imager: I can try and install the proper device OS. However, for dependency reason...
@RasPad Support Thank you, will try that. FWIW was using Raspad and running the i2cdetect command. Either the red light worked OR it was detected - but not simultaneously
@CerberusStyle cheers! I will keep plugging away’
@Nick Crosby What system are you using? If it is not raspad os, please reinstall the software.After inserting the module into the Raspberry Pi, use the command to see if the i2c address of t...
I found it. It is the USB kcable one wire was broken from the connector. What next?
@RasPad Support Please provide more information about suggestion in answer number 3 about resistor soldering. I really want to make touchscreen to work with secondary display connected.
@Nick Crosby thats linux for you so many flavours you always have to work through errors step by step, and if thats not your thing then best bet is to stick with windows, but put the time in and it...
@Efrain Santiago Same issue. I was sent a replacement accelshim, but it doesn't seem to work either. So so so frustrrating!! I get the sensor recognised as being functioning but there is no 'red li...
I'm getting cocky now .. the Raspad is booting off a Samsung 512 gb ssd. Completely OTT 🙂
@Isaac Linder ok try this go to that location,( you may need to turn on show hidden files) and create a blank/empty file called " autostart " and then try to run the command again, see if that work...
@RasPad Support OK. I just disconnected and reconnected the the cables that had the touch screen working....and now it doesn't work again. I have no idea what the problem could be. Unless you have ...
Hi @CerberusStyle Thanks for these instructions. I am in a bit of the same boat. I installed the generic Raspian (latest). The good news is that for what I'm using it for, it allows me ...
Raspad - Activate your inner innovator on demand! Raspad - Release your inner innovator! Raspad - Become an innovation beast!
@RasPad Support I borrowed a mini hdmi cable (1 meter long) and used it in in place of the long hdmi. The touch screen worked. It looks as though the problem is with the mini hdmi cables that ...
My ethernet port seems to be dead. Ifconfig says no packets, no errors, and there are not lights on the plugs. Was working last night but was dead when it rebooted this morning. Cable tested ok on ...
Mine got extremely noisy after a couple of weeks. Had to replace it. Pretty cheap repair, though
I can't swap and plug-in both cables without damaging either the board on the pad or the raspberry pi. I've tried switching the ends of the cables and it still won't go in without putting too much ...
@RasPad Support The first Pi4 8gb will not boot, tried several sd cards & os variants. Second Pi4 works fine now & is installed the Raspad. Messing around with it now! Thank you for re...
@Jay Bee Hi. I bought another Pi4 8gb, no joy with that either, to begin with. My son is far more Pi aware than I am, he declares the 1st Pi4 'dead'. Persisted with the 2nd Pi4, set it up 1st ...
Raspad - Making learning tech fun and portable. Raspad - Making your PI more.
@David Dyche There is no official screen protector. If you need it, it is recommended that you buy a 10.1-inch screen protector for Android Pad.
When you install any OS other than raspad OS the touch rotate wont work, as the software you need to make it work is specific to raspad os and has to be manually installed and configured from their...
Hi @Efrain Santiago, If no error is reported, please calibrate before starting automatic rotation. https://raspad.readthedocs.io/en/latest/faq/RasPad3-FAQ.html#q-the-direction-of-the-display-does...
@George Olive It may be that my expression is not clear. Sorry for the inconvenience cause.😅 Please plug in both HDMIs after swapping.
@RasPad Support I swapped the shorter cable for the longer one and the same results. I couldn't connect the longer cable where the short cable was without damaging my Rasspberry Pi. I figured ...
@George Olive Please swap the two HDMI cables as shown in the image. Give feedback about the test results.
My take on it: Raspad: Enjoy some Raspberry Pi anywhere and anytime you want it! A shorter version: Raspad: Raspberry Pi anywhere and anytime you want it! Or something in between! ;-)
@Thomas Veach Save the screenshot on your computer first, and then click this icon to upload the picture.
@Michael Blomquist Thanks. I attempted to route the cables as you had but mine are too short.
@RasPad Support I plugged my mouse into the 3 USB ports on the pad. It worked in all the ports.
Free your Pi from the desk with a Raspad and let it work wherever you go.
Raspad: Pi in a Box
@Thomas Veach click the insert image button its the one that look like a sunset image to the right of the smilie face.
My experiments also include field use. Is there a cover to protect the pad? or even a screen protector? Sorry, if this is already answered, but I didnt see any products or hints. ...
Raspad: It's up to you'RaSp!
Raspad: The OS Independent Tablet
@Mario Marais You'll need to adapt a USB C plug and HDMI. Also stretch out the USB Power to the HDMI due to USB sockets moved to other side of Network connection. An alternative might be POE? Stil...
How do I insert a screenshot here?
I'm a fan of LEXAR 633X 64gb v30 cards myselfe. About $10 (US).
VESA Compliant mounting.
RasPad: Have your Pi and tote it too
Raspad - The Raspberry Pi idea oven
My suggestions: Raspad, the easy way to compute and discover the digital world! Raspad, the digital world at your hands: Touch, Learn, Enjoy! Raspad, the adventure device!