@Luke Howard screen rotate does work correctly, in both portrait AND landscape views, i have been using mine in both for awhile. The fact that it wont stand on its side with anything plugged in is ...

@Luke Howard yes thats correct, its generated by the LCD controller and should really say " no signal " same as if you had a normal monitor, but as i have said the team behide raspad3 are not nativ...

@Luke Howard apologies, portrait mode does work although the screen does not adjust properly

Just installed my Raspad and set up. I also had a problem with the auto-rotate script, but I noticed it seemed to be an issue with the 'apt update' instruction. when I ran this instruction in the t...

It seems likely to me that the 'No cable' message is generated by the Raspad display system when it does not find an Raspberry pi. I see it when I have shut down the Pi before I power off the Raspa...

@Jozua Hattingh ok so what exactly is your issue with you raspad3s, because as you can see from all the other posts " no cable " can mean alot of things. If you dont say exactly what you are seein...

I have 3 Raspads for my kids and all of them do the same with working RPi. But I will again test them and the outputs and get back.  Thanks. 

@Myriri Myri you need to look at this from a technical perpective, an inconsistant issue is impossible to fully account for as if an issue can not be replicated in a cotrolled enviroment, then a pe...

@CerberusStyle As mentioned previously. The issue is inconsistent with Pi4s. Not all of them display it.  Some have the sensitivity and others do not. If using properly shielded cables its no...

@Myriri Myri hmm, so how can this issue be replicated? in my testing i see no issue, and i have exactly the same cables as anyone else does. Is it actually a flaw in the pi4 itself if so then ther...

@CerberusStyle in all probability because the HDMI wifi flaw isn't consistent among Pi4s. Some suffer from it more than others which is why the official HDMI lead is triple shielded.  ** Offe...

@Myriri Myri well thats odd cause i have it working just fine here, both wired and wifi work a treat.

I have concluded that yes it seems to be the supplied micro HDMI to micro HDMI cables are not properly shielded and thus basically useless if you intend to use wifi. 

@Frederic Dubois  There should be no problems with compatibility. Raspad has basically no effect on Raspberry Pi. If it can be used on the original Raspberry Pi, it can also be used on raspad.

@Frederic Dubois well raspad OS is EOL and should not be used so just install Raspberry PI OS 32bit or even 64bit Beta, it shouldnt matter as the program isnt architechure specific as its coded in ...

I would like to install Jeedom ( https://www.jeedom.com/en/index.html ) and keep raspad as mainboard. What about compatibility with Raspad OS? is it possible or only a dream? Maybe someone ...

Yes

yes its legit

For those who want to keep the accelshim, this might be helpful:   40 Pin GPIO Stacking Header  

@anon anon No comparison.

Thank you very much for the keybord gift. Has arrived safely at my home promptly after you annoucement. :-)

Agreed.   (1) I had removed the accelshim as it was of no use for me. So, I am not missing the auto-rotation. If it would really be need, then a short extension cord would help as the GPIO p...

@Jay Bee A neat solution i can see two drawbacks with this solution. 1. The accelshim is missing and can not be fitted, with that cooler on without modification to the cooler 2.  The PI can ...

@Steve Thompson well there we go then glad you found your problem, that why i ask so many questions to start, that way we always get to the bottom of the problem. 

Source: Click

#8: Final Solution on Heat Management: See here: https://raspad.com/community/forum/topic/35813/finale-solution-heat-management

Armor Case (Berrybase). Around 35°C at idle Below 60°C at high loads

I've swaqpped out the RPI 4 that I bought alongside the Raspad for a known working RPI4 that I was using for other things.  It looks like the "new" RPI is the problem as my older one has boote...

@Steve Thompson ok please provide the image of inside the raspad3, so i can see the connections. Then remove the two HDI cables, and plug the external display directly to the pi and try to boot do...

Whe I try to boot with an external monitor attached to the Raspad 3 I get notthing at all on the external monitor and just the No Cable message on the Raspad then blank screen.

@Milky Pimms no problems glad i could help.

@CerberusStyle Cheers I prob's use Twister, raspberry PI OS come's with VS code pre installed - mircopoo (microsoft) malware add to the repo list. Thanks again great hardware made easy.

@Milky Pimms  Hold up your using raspad OS ? if so then thats the issue raspad OS no longer exists (EOL) you need to install standard raspberry PI OS and then the raspad launcher if you want ...

Still no good.. I'm Not a fan of the raspad image O/S but hardware is good.

@CerberusStyle Thanks dude.

@Steve Thompson Ok as i supected the fact "no cable" is shown didnt tell the whole story, all that message is, is the main board in the raspad3 saying that it is not recieving a HDMI output from y...

When I press and hold  the power button, the 3 green lights and the red light all come on, after a few seconds the "No Cable" message comes on for 2-3 seconds then disappears, the screen is bl...

Ok that not a raspad3 issue but an issue with your install, dont use etcher to write your image use the offical RPI imager and install a fresh copy of RPI OS. and you will be fine.  https://w...

The raspad3 and ipad air are two completely diferent animals, so can not be compared.  If you want an end user polished devices locked to a single ecosystem (macos) then buy an ipad air. If ...

Is there any thorough display review of it?

Hi all, Help please, Can not connect my raspad to WiFi I get: Error saving /etc/dhcpcd.conf The dhcpcd configuration file is not wirteable. The image is on a USB 3.0 stick in the pi4 and used bale...

ok so what exactly is your issue, because as you can see from all the other posts " no cable " can mean alot of things. If you dont say exactly what you are seeing then no one will ever be able to ...

I have seen the other posts referenci9ng the No Cable on boot up, read them all and the responses and tried them all to no avail!  What is the issue here, after reseating all the cables (5 tim...

@JD Gramajo  Please send us a message about your order number or backer number.And attach your shipping address and telephone in order to arrange delivery.Message steps:Click on the avatar&nb...

Hi, thanks for such an awesome product! All was well and good, today when I wanted to start my RasPad it showed me the following: I proceeded to thoroughly check everything and finally arrived ...

@Dave R  You can refer to this method to uninstall the topic: https://github.com/raspad-tablet/raspad-launcher/blob/main/docs/installation-guide.md#change-menu-back